IMPACT PRO

Market leading, very flexible portable gas detector, capable of monitoring 4 gases at once.

Using high specification flammable, Oxygen and patented Surecell™ toxic sensors, our unique cartridge technology ensures safe, accurate and reliable measurements are always made.

Available in two configurations, the Impact and Impact Pro accepts either disposable and/or serviceable cartridges respectively, all of which are pre-calibrated and can be replaced in under one minute, simplifying maintenance and minimizing cost wherever possible. Compact and rugged, these monitors are designed for tough working environments while being small, lightweight and unobtrusive, making them ideal for use in confined spaces where entry and exit may be difficult.

Gas checks prior to entering a confined space can be carried out using a drop line, hand aspirator or via an optional built-in pump (supplied as standard on the Impact Pro) that turns on and off automatically when the sampling tube is connected.

Ultra-bright alarm lights and a powerful audible alarm, coupled with a periodic green flash and bleep provide user confidence that monitoring is always in operation and alarms are never missed. For noisy environments a vibrating alarm is included as standard on the Impact Pro. A large, multi-lingual, backlit display, with intuitive menu system simplifies use and minimises operator training.

Available for use with a wide range of accessories including the unique Enforcer calibration system and compliance friendly Safelink communication system, the Impact range of portable multigas monitors is ready to protect you when most needed.

Reliable Operation
• Pre-calibrated plug-in sensor cartridge
• High specification sensors
• Patented Surecell™ toxic sensors
• Stable and accurate

Easy to Use
• One button on/off
• Multi-lingual, intuitive menu system
• On screen prompts guide user
• Built-in correction factors for flammable gases
• Minimal training required
• Plug-in operation for all serviceable parts
• Cartridge replacement in less than one minute
• Re-calibration in less than two minutes when using Enforcer
• Minimised cost of ownership

Durable Housing
• Waterproof to IP67
• Rugged and impact resistant
• Built for everyday use

Alarm Indication
• 3 levels of instantaneous alarm, time weighted average alarms on toxic
• Periodic confidence flash and bleep
• Increasingly rapid flashing, ultra-bright alarm LEDs
• Powerful two tone audible alarm
• Vibrating alarm for noisy environments*
• Safelink communications*

User Friendly Pre-entry Check
• Peak hold function and drop line
• Hand aspiration
• Built-in automatic pump*
• Totally flexible

* Impact Pro model only

Enforcer Calibration Accessory

The Enforcer provides easy and cost-effective 'bump testing' for the Impact range of multi gas detectors.

Regulations require regular testing of gas monitoring equipment to ensure that the instrument will work as and when required.

The Enforcer allows you to easily comply with regulations when using an Impact multi-gas monitor without the need for costly test facilities or third parties.

‘Bump’ testing should be carried out before use of any portable gas detector. This involves exposing each gas sensor to a known concentration of target gas and ensuring that it responds correctly. If not, the unit must be re-calibrated or serviced to replace those parts not working.

Personal gas monitors are normally calibrated every 3 to 6 months. Typically this requires specialist knowledge and equipment that is costly or the work is sub-contracted to a third party. During this time instruments are not available for use and so could delay essential operations or force additional monitors to be purchased.

The Enforcer calibrates Impact multi-gas monitors fitted with Oxygen, flammable, Carbon Monoxide and Hydrogen Sulphide sensors in less than two minutes. Volumes and flow rates are minimised to allow approximately 200 calibrations per cylinder of gas making calibration as low in cost as a ‘Bump’ test.

Impact instruments when used with the Enforcer are always available for use. Calibration results are recorded for printing at a later date via the optional PC software thereby ensuring that instrument histories are always available if required

Convenient to Use
• Portable design
• Lightweight and compact
• Disposable multi-gas cylinder
• Wall mounting bracket with security fixing included

Easy to Operate
• Simple mechanical construction
• Attach the Impact
• Instrument is automatically recognised
• Press a single button to proceed
• Wait a minute
• Impact is now tested and calibrated
• Minimal training required

Minimise Running Costs
• No need for third parties
• Reduce instrument downtime
• Simplify operations
• Minimise gas consumption

Easy to Maintain
• Durable plastic housing
• Wipe clean surfaces
• Replaceable gaskets and seals
• Built-in indicator tells you when gas needs replacing

Maintain Records
• Calibration history recorded by instrument
• Print history via optional PC software
• Ensure compliance with regulation